{"product_id":"80-105-series-landcruiser-rear-panhard-riser-rampt-customs","title":"80\/105 Series LandCruiser Rear Panhard Riser - Bolt on Kit Options","description":"\u003cp\u003e\u003cspan\u003eThe Rampt Customs Rear Panhard Riser is a bolt-on suspension geometry correction designed for Toyota 80 Series and 105 Series LandCruisers. It raises the rear panhard mounting point by 3 inches, helping bring the panhard closer to horizontal on a lifted vehicle and reducing the amount of lateral axle movement produced as the suspension travels through bump and rebound.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eOn a lifted 80 or 105 Series, the factory panhard operates at a greater angle than it does at standard ride height. Because the rear axle follows the arc of the panhard as the suspension moves, this angle can contribute to greater side-to-side axle movement through the suspension cycle. Raising the mounting position changes that geometry and also raises the rear roll centre, with Rampt designing the system to improve stability and reduce the body movement and rear-end lateral movement commonly felt in lifted Cruisers.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eThe bracket attaches to the original rear panhard mount on the differential housing and the passenger-side upper control arm mount. Installation of the bracket itself requires no cutting, grinding, drilling or welding. Rampt Customs designs and manufactures its 4WD suspension and fabrication components from its workshop in Newcastle, NSW.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003e\u003cspan\u003eTwo Panhard Mounting Positions\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003e\u003cspan\u003eThe Rampt riser provides two alternative mounting positions depending on the panhard being used.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan\u003ePosition 1\u003c\/span\u003e\u003c\/strong\u003e\u003cspan\u003e raises the panhard mount 3 inches and moves the mounting point approximately 1 inch farther across. This position accepts the factory-style Toyota panhard bush, but the standard factory panhard is too short for the relocated mounting point. An aftermarket adjustable panhard is required so the rear axle can be correctly centred beneath the vehicle.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan\u003ePosition 2\u003c\/span\u003e\u003c\/strong\u003e\u003cspan\u003e is also 3 inches higher but extends the effective mounting position approximately 4 inches farther across. It is specifically designed for the Rampt extended rear panhard offered with this kit.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eA longer panhard operates through a larger-radius arc, reducing the amount of sideways axle displacement generated for a given amount of vertical suspension travel. This is why panhard rods are generally designed to be as long and as close to horizontal as practical within the available suspension geometry.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003e\n\u003cspan\u003eExtended 7075-T6 Panhard\u003c\/span\u003e\u003cspan\u003e\u003c\/span\u003e\n\u003c\/h3\u003e\n\u003cp\u003e\u003cspan\u003eThe extended panhard is manufactured from solid 1.5 inch \/ 38.1 mm 7075-T6 aluminium and uses a Whiteline polyurethane bush at one end. The opposite end can be supplied with either a 7\/8 inch DFI three-piece heim or a 7\/8 inch FK rod end, depending on the selected variant. \u003c\/span\u003e\u003cspan\u003eThe heim joint allows angular misalignment through the panhard's operating range while the polyurethane bush provides the bushed chassis or axle connection used in Rampt's design.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003e\u003cspan\u003eMinimum 70 mm Bump Stop Extension Required\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003e\u003cspan\u003eThis is an important fitment requirement. T\u003c\/span\u003e\u003cspan\u003ehe outer rear bump stops located beneath the chassis rails must be extended by a minimum of 70 mm when the panhard riser bracket is fitted. This provides the clearance required to prevent the riser bracket contacting the chassis at full bump.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eBump stop extensions are available as part of selected kit options. \u003c\/span\u003e\u003cspan\u003eDo not fit the riser bracket without confirming adequate bump stop extension and clearance throughout the full suspension travel.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003e\u003cspan\u003eWhich Kit Option Do I Need?\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan\u003eBracket Only\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eIncludes the rear panhard riser bracket. \u003c\/span\u003e\u003cspan\u003eYou will still require:\u003c\/span\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cspan\u003eMinimum 70 mm outer bump stop extensions\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cspan\u003eA suitable aftermarket adjustable panhard\u003c\/span\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan\u003eThe factory panhard itself is too short for the relocated mounting position.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan\u003eBracket \u0026amp; Bump Extensions\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eIncludes the rear panhard riser bracket and Rampt bump stop extensions. \u003c\/span\u003e\u003cspan\u003eYou will still require a suitable aftermarket adjustable panhard.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan\u003eBracket \u0026amp; Extended Panhard – DFI Heim\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eIncludes the rear panhard riser bracket and extended 7075-T6 panhard with 7\/8 inch DFI three-piece heim. \u003c\/span\u003e\u003cspan\u003eYou will still require minimum 70 mm outer bump stop extension if this is not already fitted to the vehicle.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan\u003eBracket \u0026amp; Extended Panhard – FK Heim\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eIncludes the rear panhard riser bracket and extended 7075-T6 panhard with 7\/8 inch FK rod end. \u003c\/span\u003e\u003cspan\u003eYou will still require minimum 70 mm outer bump stop extension if this is not already fitted to the vehicle.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan\u003eBracket, Bump Extensions \u0026amp; Panhard – DFI Heim\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eIncludes the rear panhard riser bracket, bump stop extensions and extended 7075-T6 panhard with 7\/8 inch DFI three-piece heim. \u003c\/span\u003e\u003cspan\u003eThis is the complete Rampt configuration using the extended panhard.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan\u003eBracket, Bump Extensions \u0026amp; Panhard – FK Heim\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eIncludes the rear panhard riser bracket, bump stop extensions and extended 7075-T6 panhard with 7\/8 inch FK rod end. \u003c\/span\u003e\u003cspan\u003eThis is the complete Rampt configuration using the extended panhard.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan\u003eExtended Panhard Only – DFI Heim\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eExtended 7075-T6 panhard with 7\/8 inch DFI three-piece heim and Whiteline polyurethane bush. \u003c\/span\u003e\u003cspan\u003eThis panhard is designed for the extended mounting position provided by the Rampt rear panhard riser bracket.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003e\u003cspan\u003eExtended Panhard Only – FK Heim\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eExtended 7075-T6 panhard with 7\/8 inch FK rod end and Whiteline polyurethane bush. \u003c\/span\u003e\u003cspan\u003eThis panhard is designed for the extended mounting position provided by the Rampt rear panhard riser bracket.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003e\u003cspan\u003eLift Height\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003e\u003cspan\u003eRampt lists the rear panhard riser as suitable across lift heights, while stating that the suspension geometry produces its best results at approximately 3 to 4 inches of lift or less. Rampt also notes that vehicles with a 2 to 3 inch lift can see a particularly noticeable improvement compared with taller 4 to 6 inch setups. \u003c\/span\u003e\u003cspan\u003eThe actual panhard angle, bump clearance and axle position should always be checked on the individual vehicle rather than relying on nominal lift height alone.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003e\u003cspan\u003eInstallation \u0026amp; Rear Axle Alignment\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003e\u003cspan\u003eAfter installation, the rear axle must be correctly centred beneath the chassis. \u003c\/span\u003e\u003cspan\u003eWe recommend measuring between consistent reference points on the chassis and tyres before installation, then adjusting the panhard after installation until the corresponding measurements are matched.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eFor the bracket mounting hardware, Rampt specifies:\u003c\/span\u003e\u003c\/p\u003e\n\u003cul\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cspan\u003eM18 bolt through the original panhard mounting position: \u003c\/span\u003e\u003cstrong\u003e\u003cspan\u003e70 Nm\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cspan\u003eM16 bolt through the upper control arm mounts: \u003c\/span\u003e\u003cstrong\u003e\u003cspan\u003e70 Nm\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003cli\u003e\n\u003cp\u003e\u003cspan\u003eBolt through the new panhard mounting position: \u003c\/span\u003e\u003cstrong\u003e\u003cspan\u003eToyota factory torque specification\u003c\/span\u003e\u003c\/strong\u003e\u003c\/p\u003e\n\u003c\/li\u003e\n\u003c\/ul\u003e\n\u003cp\u003e\u003cspan\u003eRampt specifically states that the M18 and M16 mounting bolts listed above should be tightened to 70 Nm only. \u003c\/span\u003e\u003cspan\u003eClearance should then be checked throughout the suspension's usable range of travel for your individual vehicle setup.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003e\u003cspan\u003eImportant Fitment Information\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003e\u003cspan\u003eThis product is designed for Toyota 80 Series and 105 Series LandCruisers \u003c\/span\u003e\u003cspan\u003eAn aftermarket adjustable panhard is required when using the first riser mounting position. The original factory panhard is not long enough for the relocated mounting position.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eThe Rampt extended panhard is intended for the second, extended mounting position on the Rampt riser bracket. \u003c\/span\u003e\u003cspan\u003eMinimum 70 mm outer bump stop extensions are required whenever the riser bracket is installed. \u003c\/span\u003e\u003cspan\u003eSuspension clearance varies depending on lift height, shock length, bump stop configuration, tyre size and other vehicle modifications. Full bump, droop and component clearance should be checked for the individual vehicle after installation.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eRampt Customs also states generally that, unless otherwise specified, its products are designed for off-road use. Vehicle modification and engineering requirements vary between Australian states and territories, so confirm the requirements applicable to your vehicle before installation.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003e\u003cspan\u003eShipping Australia Wide\u003c\/span\u003e\u003c\/h3\u003e\n\u003cp\u003e\u003cspan\u003eOrders are dispatched quickly from Australia. Questions? Hit us up, we're 4WDers too and happy to help.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch3\u003e\u003cspan\u003eSpecifications\u003c\/span\u003e\u003c\/h3\u003e\n\u003ctable\u003e\n\u003ctbody\u003e\n\u003ctr\u003e\n\u003cth colspan=\"2\"\u003eFitment \u0026amp; Geometry\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eVehicle Compatibility\u003c\/td\u003e\n\u003ctd\u003eToyota 80 Series \u0026amp; 105 Series LandCruiser\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eInstallation\u003c\/td\u003e\n\u003ctd\u003eBolt-on bracket; no cutting, grinding, drilling or welding required\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMount Position 1\u003c\/td\u003e\n\u003ctd\u003e3\" higher and approximately 1\" farther across; accepts factory-style Toyota panhard bush; aftermarket adjustable panhard required\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMount Position 2\u003c\/td\u003e\n\u003ctd\u003e3\" higher and approximately 4\" farther across; designed for Rampt extended panhard\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eMinimum Bump Stop Extension\u003c\/td\u003e\n\u003ctd\u003e70 mm outer rear bump stop extension required\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eFinish\u003c\/td\u003e\n\u003ctd\u003eSatin black powder coat\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth colspan=\"2\"\u003eExtended Panhard\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eConstruction\u003c\/td\u003e\n\u003ctd\u003eSolid 7075-T6 aluminium\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eDiameter\u003c\/td\u003e\n\u003ctd\u003e1.5\" \/ 38.1 mm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eHeim Options\u003c\/td\u003e\n\u003ctd\u003e7\/8\" DFI three-piece heim or 7\/8\" FK rod end\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eBushed End\u003c\/td\u003e\n\u003ctd\u003eWhiteline polyurethane bush\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003cth colspan=\"2\"\u003eInstallation Torque\u003c\/th\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM18 Factory-Location Panhard Bolt\u003c\/td\u003e\n\u003ctd\u003e70 Nm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eM16 Upper Link Mount Bolt\u003c\/td\u003e\n\u003ctd\u003e70 Nm\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003ctr\u003e\n\u003ctd\u003eNew Panhard Location Bolt\u003c\/td\u003e\n\u003ctd\u003eTorque to Toyota factory specification\u003c\/td\u003e\n\u003c\/tr\u003e\n\u003c\/tbody\u003e\n\u003c\/table\u003e\n\u003ch3\u003e\n\u003cspan\u003e\u003c\/span\u003e\u003cbr\u003e\n\u003c\/h3\u003e\n\u003ch3\u003e\n\u003cspan\u003eFAQ's\u003c\/span\u003e\u003cspan\u003e\u003c\/span\u003e\n\u003c\/h3\u003e\n\u003ch4\u003e\u003cspan\u003eWill the rear panhard riser change how my LandCruiser handles?\u003c\/span\u003e\u003c\/h4\u003e\n\u003cp\u003e\u003cspan\u003eYes, that is the purpose of correcting the panhard geometry. \u003c\/span\u003e\u003cspan\u003eRaising the rear panhard mounting point brings the bar closer to horizontal on a lifted 80 or 105 Series LandCruiser. This reduces the amount of lateral axle movement generated as the suspension moves through its travel and raises the rear roll centre.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eThe result should be improved stability, reduced body roll and less of the rear-end lateral movement often felt over bumps in lifted vehicles. The amount of change you notice will depend on your lift height, existing suspension geometry and overall vehicle setup.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch4\u003e\u003cspan\u003eWill the panhard riser affect suspension flex?\u003c\/span\u003e\u003c\/h4\u003e\n\u003cp\u003e\u003cspan\u003eThe riser is designed to change the path of the rear axle rather than prevent the suspension from articulating. \u003c\/span\u003e\u003cspan\u003eWe recommend a minimum 70 mm extension to the outer rear bump stops so the riser cannot contact the chassis at full bump. Shock length, bump stop height, spring setup and other suspension modifications can all influence the usable travel available on an individual vehicle.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eFor this reason, we recommend checking clearance through the suspension's operating range after installation rather than assuming every modified 80 or 105 Series will behave identically.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch4\u003e\u003cspan\u003eWill my existing aftermarket panhard work with the riser?\u003c\/span\u003e\u003c\/h4\u003e\n\u003cp\u003e\u003cspan\u003eA suitable aftermarket adjustable panhard can be used with the first mounting position. \u003c\/span\u003e\u003cspan\u003eThis mounting position is approximately 1 inch farther across than the original location, so the panhard needs enough adjustment to correctly centre the rear axle beneath the vehicle.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eThe original fixed-length Toyota panhard is too short for the relocated position. \u003c\/span\u003e\u003cspan\u003eIf you're unsure whether your current panhard has enough adjustment, email us at \u003c\/span\u003e\u003ca href=\"mailto:info@northadventures.com.au\"\u003e\u003cstrong\u003e\u003cspan\u003einfo@northadventures.com.au\u003c\/span\u003e\u003c\/strong\u003e\u003c\/a\u003e\u003cspan\u003e with the brand or a photo of your current setup and we'll help you work through it.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch4\u003e\u003cspan\u003eI only have a 2 to 3 inch lift. Is the panhard riser still worthwhile?\u003c\/span\u003e\u003c\/h4\u003e\n\u003cp\u003e\u003cspan\u003eThe riser can be used across a range of lift heights, with approximately 2 to 4 inches being a particularly relevant range for correcting rear panhard angle. \u003c\/span\u003e\u003cspan\u003eThe actual benefit depends more on the panhard angle and suspension geometry of the individual vehicle than the advertised lift height alone.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch4\u003e\u003cspan\u003eDo I need to centre the rear axle again after installation?\u003c\/span\u003e\u003c\/h4\u003e\n\u003cp\u003e\u003cspan\u003eYes, as\u003c\/span\u003e\u003cspan\u003e the new panhard mounting position changes the effective geometry and length required, the rear axle should be checked and re-centred after installation. \u003c\/span\u003e\u003cspan\u003eWe recommend taking measurements between consistent chassis and tyre reference points before removing the original setup, then adjusting the panhard after installation until the corresponding measurements are equal. \u003c\/span\u003e\u003cspan\u003eIt is also worth checking the axle position before beginning, as the rear diff may not have been perfectly centred beforehand.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch4\u003e\u003cspan\u003eWhat is the advantage of the extended panhard?\u003c\/span\u003e\u003c\/h4\u003e\n\u003cp\u003e\u003cspan\u003eThe extended panhard uses the second mounting position on the riser, which places the connection approximately 4 inches farther across than the original mounting position. \u003c\/span\u003e\u003cspan\u003eIncreasing the effective panhard length increases the radius of the arc the axle travels through. For the same amount of vertical suspension movement, a longer panhard therefore produces less lateral axle displacement than a shorter one.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eThe extended panhard is manufactured from solid 1.5 inch \/ 38.1 mm 7075-T6 aluminium and is available with either a 7\/8 inch DFI three-piece heim or an FK rod end, with a Whiteline polyurethane bush at the opposite end. \u003c\/span\u003e\u003cspan\u003eThe standard riser position remains available for customers who already have a suitable adjustable panhard, while the extended option provides the longer-panhard geometry.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch4\u003e\u003cspan\u003eDo I need extended bump stops?\u003c\/span\u003e\u003c\/h4\u003e\n\u003cp\u003eYes. We recommend a minimum 70 mm extension to the outer rear bump stops located beneath the chassis rails whenever the panhard riser bracket is fitted. This clearance is required so the riser bracket cannot contact the chassis at full bump. \u003cspan\u003eWe do not recommend installing the riser without confirming the required bump stop extension and checking clearance on your individual suspension setup.\u003c\/span\u003e\u003c\/p\u003e\n\u003ch4\u003e\u003cspan\u003eWhich kit should I order?\u003c\/span\u003e\u003c\/h4\u003e\n\u003cp\u003e\u003cspan\u003eIf you already have a suitable adjustable aftermarket panhard and at least 70 mm of outer rear bump stop extension, the \u003c\/span\u003e\u003cstrong\u003e\u003cspan\u003eBracket Only\u003c\/span\u003e\u003c\/strong\u003e\u003cspan\u003e option may be all you require.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eIf you already have an adjustable panhard but still need the required bump stop clearance, choose \u003c\/span\u003e\u003cstrong\u003e\u003cspan\u003eBracket \u0026amp; Bump Extensions\u003c\/span\u003e\u003c\/strong\u003e\u003cspan\u003e.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eFor customers wanting to use the longer second mounting position, choose one of the kits containing the \u003c\/span\u003e\u003cstrong\u003e\u003cspan\u003eExtended Panhard\u003c\/span\u003e\u003c\/strong\u003e\u003cspan\u003e, available with either a DFI or FK heim.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eThe complete \u003c\/span\u003e\u003cstrong\u003e\u003cspan\u003eBracket, Bump Extensions \u0026amp; Panhard\u003c\/span\u003e\u003c\/strong\u003e\u003cspan\u003e options contain the riser, bump stop extensions and extended panhard together.\u003c\/span\u003e\u003c\/p\u003e\n\u003cp\u003e\u003cspan\u003eNot sure which setup suits your vehicle? Email \u003c\/span\u003e\u003ca href=\"mailto:info@northadventures.com.au\"\u003e\u003cstrong\u003e\u003cspan\u003einfo@northadventures.com.au\u003c\/span\u003e\u003c\/strong\u003e\u003c\/a\u003e\u003cspan\u003e with your lift height, current panhard and bump stop setup and we'll help you choose the right configuration.\u003c\/span\u003e\u003c\/p\u003e","brand":"Rampt Customs","offers":[{"title":"Bracket Only","offer_id":51235024339030,"sku":null,"price":800.0,"currency_code":"AUD","in_stock":true},{"title":"Bracket \u0026 Bump Ext","offer_id":51235024371798,"sku":null,"price":1000.0,"currency_code":"AUD","in_stock":true},{"title":"Bracket \u0026 Ext Panhard (DFI Heim)","offer_id":51235024404566,"sku":null,"price":1365.0,"currency_code":"AUD","in_stock":true},{"title":"Bracket \u0026 Ext Panhard (FK Heim)","offer_id":51235024437334,"sku":null,"price":1450.0,"currency_code":"AUD","in_stock":true},{"title":"Bracket Bump Ext \u0026 Panhard (DFI Heim)","offer_id":51235024470102,"sku":null,"price":1565.0,"currency_code":"AUD","in_stock":true},{"title":"Bracket Bump Ext \u0026 Panhard (FK Heim)","offer_id":51235024502870,"sku":null,"price":1650.0,"currency_code":"AUD","in_stock":true},{"title":"Ext Panhard Only (DFI Heim)","offer_id":51235024535638,"sku":null,"price":565.0,"currency_code":"AUD","in_stock":true},{"title":"Ext Panhard Only (FK Heim)","offer_id":51235024568406,"sku":null,"price":650.0,"currency_code":"AUD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0585\/1329\/3398\/files\/Screenshot_2026-11-20_174640.png?v=1795157584","url":"https:\/\/www.northadventures.com.au\/products\/80-105-series-landcruiser-rear-panhard-riser-rampt-customs","provider":"North Adventures","version":"1.0","type":"link"}